VEVOR Press Actuator for 24KN Compact Series Press Tools, Works with 1/2″, 3/4″, 1″ & 1-1/4″ Press Rings – Compatible with ProPress Copper Pipes (Ring NOT Included)

Press Actuator with 180-Degree Rotation Reaches Confined Copper Pipe Connections

The VEVOR press actuator can rotate 180 degrees, allowing the operator to change the press angle without disconnecting the tool from the press ring or moving the copper pipe. The ability to rotate is the main advantage of an actuator-based pressing system over fixed-jaw tools. It lets you reach connection points that are physically blocked from a straight-on approach.

When there are blocked fittings in tight wall cavities, behind mechanical equipment, or in densely packed pipe chases, fixed-jaw press tools require either rerouting the pipe or disassembling the component to reach them. The actuator eliminates both workarounds by immediately rotating to the correct approach angle.

52 HRC Hardened Carburized Steel Actuator Sustains 10,000+ High-Integrity Press Cycles

The actuator is made of carburized steel, hardened to at least 52 HRC. It can handle more than 10,000 ProPress copper pipe pressing cycles while still being completely accurate in size and shape. This hardness requirement ensures that the actuator’s internal drive parts maintain the correct pressure and torque on the press ring on every cycle, without the mechanical slop that occurs in actuator bodies that aren’t hard enough after they wear out.

Carburized construction gives the actuator a hard, wear-resistant outer layer over a core that won’t break, so it can handle the 24KN load of each press event without getting surface fatigue or internal stress fractures. An actuator rated for more than 10,000 crimps works as a long-lasting production part for HVAC contractors and plumbers who install copper pipes every day.

Compatible with 1/2″, 3/4″, 1″ & 1-1/4″ Press Rings Across 4 Copper Pipe Diameters

The VEVOR press actuator works with press rings in four sizes: 1/2″, 3/4″, 1″, and 1-1/4″. These sizes cover the most common copper pipe sizes used in residential plumbing systems, commercial HVAC water-side piping, and large-capacity hydronic distribution mains. One actuator body works with all four ring sizes, so you don’t need separate pressing tools for each pipe diameter in a mixed-size copper installation.

This actuator can be used with four different diameters, which makes it a scalable investment that grows with the contractor’s work. A plumber who works on residential supply lines at 1/2″ and 3/4″ can add 1″ and 1-1/4″ press rings later as the needs of a commercial project grow, without having to change the actuator itself.

Works with 24KN Press Tools Across 12 Models, Including MP-2430 & M12

The actuator works with VEVOR 24KN compact electric press tools, such as the MP-2430 and SL-2430, and connects directly to ten other professional press tool platforms, including the RP100-B, RP200-B, RP210-B, RP240, RP241, RP251, and M12. This range of 12 compatible models includes the most common 24KN press tools used by plumbing and mechanical contractors in the field.

Contractors with mixed-brand tool inventories and who work with multiple crews can use a single VEVOR press actuator across all 12 compatible platforms, eliminating the need to buy separate actuators for each tool. This cross-compatibility reduces the number of accessories needed, speeds up tool matching when crews switch equipment, and ensures the actuator is always ready to work with any compatible 24KN press tool on site when a ProPress copper connection is needed.

Rated for HVAC, Gas Pipelines & Radiant Heating Copper Systems

The actuator can be used with HVAC water-side piping, natural gas copper branch lines, radiant floor heating distribution systems, and other types of commercial plumbing. The four ring sizes that work with these applications range from 1/2″ to 1-1/4″. Together, they cover common copper pipe sizes used in both residential and commercial settings.

When installing radiant heating systems, the actuator’s ability to turn 180 degrees is especially useful when the pipes are already in place, and the structural framing sets the access angles. This is because the copper distribution lines are often cast into concrete floor slabs. Before the slab is poured, every connection should be pressed correctly.

Flameless ProPress Actuator System Removes Torch Risk from 4-Diameter Copper Work

A press actuator system eliminates open-flame brazing and torch soldering for all four compatible ProPress copper connection diameters. Using a single flameless press cycle instead of torch work takes away the risk of fire in wall cavities, mechanical rooms, and occupied buildings where insulation, framing, and flammable materials are near the pipe connection points. This safety improvement applies to all connections made with the actuator, not just some based on size or location.

On regulated commercial job sites where every torch operation requires a hot-work permit, switching to the actuator system means ProPress copper connections don’t require a permit. You can test each pressed joint right away after the press cycle is over. These savings in time, materials, and administrative costs add up to a measurable reduction in total project cost across a full copper installation with mixed diameters.

R8-24 Actuator Performs Across Residential Retrofits & Commercial Pipe Installations

The VEVOR R8-24 actuator works well for both residential plumbing retrofits with a few hard-to-reach connections and large commercial copper pipe installations, where its 180-degree rotation and four-ring compatibility are used across hundreds of connection points with varying diameters. The actuator’s 10,000+ cycle rating means it will stay mechanically reliable long after the connection count of any one project.

For residential installers, the actuator’s ability to rotate makes it easier to work in finished spaces where the angles of approach to pipe fittings are set by wall framing and can’t be changed. The actuator’s 12-model cross-compatibility and long-lasting performance of ≥52 HRC over extended periods of high-volume use make it easy for commercial contractors to use it in any professional pressing workflow.