VEVOR Electric Meat Bandsaw Stand, Floor Stand with Adjustable Height, Stable H-Shaped Frame, Anti-Slip Foot Pads, for Our Bone Saw Machine, Compatible with Models BS-130 & BS-250

VEVOR Bandsaw Stand with 7-Level Adjustable Height from 23.6 to 39.4 Inches

The VEVOR bandsaw stand can be set to seven heights, ranging from 23.6 to 39.4 inches. This wide range of adjustments works for people of different heights who operate in diverse places. Setting the right working height makes extended cutting sessions far less tiring. When the equipment is too low, workers have to bend forward constantly.

With seven fixed-height positions, you can make substantial adjustments without the hassle of continuously adjustable systems. There is no play or flex between settings, and each position locks solidly. You only have to set it once for the position you like to work in, and it stays there. The option to change the height between users is a real benefit for butcher shops, meat processing plants, and industrial kitchens where multiple people use the same machine.

Stable H-Shaped Frame for Rigid, Vibration-Resistant Support During Cutting

The frame of this bandsaw stand is designed like an H. This design spreads the weight of the mounted machine over four contact points at the base. Four-point contact is far more stable than the two-point leg designs that are popular on lighter stands. The H-frame doesn’t rock or shift sideways when the bone saw is under stress.

When bone saw machines are working, they make a lot of noise. This vibration goes straight into the stand and the floor below it. A weak or poorly built platform worsens this vibration, causing the machine to move around while in use and leaving the operator more tired. The H-shaped frame does a good job of absorbing and spreading vibration throughout its whole structure.

Precision Hole Fixing System for Secure Machine-to-Stand Attachment

The mounting technique for this bandsaw stand locks the bandsaw to the platform by lining up the holes. The machine drops into place cleanly without being forced or shimmed if the holes are in the right spot. When the mounting gear is tightened, the machine and the stand become one solid unit.

When using a bone saw, it is very important to make sure the machine is securely attached to the stand for safety. It is unsafe for the operator to use a machine that moves or lifts during cutting. The precision hole fixing system eliminates this risk by ensuring the machine can’t come apart or move under typical operating stresses. I

Powder-Coated Iron Construction for High Load Capacity and Rust Resistance

This bandsaw stand is made entirely of iron and has a powder-coated finish. Iron gives the structure the strength and mass it needs to support a commercial bone saw machine without bending or flexingunder loaded. The stand is 29.1 inches wide, 18.9 inches deep, and 39.4 inches tall when fully extended, and it weighs 24.3 pounds on its own.

Powder coating protects iron surfaces from rust, corrosion, and chemical exposure in moist commercial settings. Butcher shops and meat-processing facilities are always exposed to water, blood, and cleaning products. Under these conditions, an iron stand that is not painted or covered would rust very quickly. The powder-coat finish creates a strong, sealed surface layer that helps block moisture and contaminants.

Anti-Slip Foot Pads for Safe, Stable Floor Contact on Wet or Smooth Surfaces

There are four anti-slip foot pads on the bottom of each stand leg. These pads create friction between the stand and the floor beneath it. A stand without foot pads slides when it vibrates on smooth tile, sealed concrete, or wet kitchen floors. This sliding makes things unsafe because the whole machine-and-stand combo moves during cutting. This won’t happen because of the anti-slip pads.

The pads also protect the floor from scratches or marks when you use it normally. Hard iron legs drag across tile or sealed concrete, leaving scuffs and degrading the floor finish over time. The rubber pad material absorbs contact and acts as a cushion between the iron leg and the floor. This protection is useful for businesses with strict rules for maintaining clean floors.

Compatible with VEVOR BS-130 and BS-250 Bone Saw Machine Models

This platform was made and tested just for VEVOR’s BS-130 and BS-250 bone saw machines. The mounting hole pattern, platform size, and load capacity are matched to these two models. Before sale, the product is tested for compatibility. You don’t need to guess, measure, or change anything to see if the stand will work with your machine. It is a solution made just for these units.

Using a stand made for a specific purpose instead of a generic one removes any doubt about how well it will fit. Generic supports need to be drilled, shimmed, or mounted using unique methods, which takes more time, costs more, and could be dangerous. A stand that has been proven to be compatible installs quickly and correctly the first time. VEVOR support has also confirmed that the HC-210 bone saw model works with the other tools. It makes the stand a useful and safe improvement for any place that already has VEVOR bone saws.

Dedicated Bandsaw Stand Solution That Clears Counter Space for a Cleaner Workspace

Putting a bone saw machine right on a countertop takes up critical prep space in homes or businesses where meat is cut. Putting the machine on a separate floor stand frees up counter space for other processing chores, including preparing, packaging, and processing meat. A cleaner, more organized workspace makes it easier to get things done and reduces the risk of cross-contamination between tasks.

The floor stand also puts the machine at a more natural standing height than most countertops. Most kitchen counters are 36 inches high, which is typically too low for comfortable bone-saw use over long periods. This stand has seven height settings that reach 39.4 inches, so that you can place the machine above the counter for a more comfortable working angle.