VEVOR Condensate Pump, 1/12 HP, 90 GPH, 20 ft Lift, 115V Automatic AC Condensation Removal Pump with Safety Switch 20 ft Tubing, for Air Conditioner, Dehumidifier, HVAC, Furnace, Ice Maker Water Drain

1/12 HP Motor at 3500 RPM Powers the Automatic Condensate Pump Beyond Standard Drainage Limits

The VEVOR automatic condensate pump features a powerful 1/12 HP (60W) motor that spins at 3500 RPM, providing a steady mechanical force suitable for demanding drainage applications. This motor setup creates enough torque to keep the system running continuously through long drainage cycles without overheating or losing performance.

Technicians who install this unit in high-load applications, such as commercial HVAC systems or multi-zone mini-split setups, will appreciate its consistent performance. The motor’s RPM rating ensures drainage starts quickly, even when the rate of condensate buildup changes. It reduces the time between when water is detected and when pumping starts.

90 GPH Maximum Flow Rate Handles High-Volume Condensate Output Across HVAC and Dehumidifier Applications

This automatic condensate pump can move up to 90 gallons per hour at its highest operational capacity. This feature makes it a good choice for places where humidity levels or continuous cooling cycles accelerate condensate formation. This flow rate allows dual-inlet systems to drain simultaneously without losing pressure or risking backflow.

The 90 GPH throughput of dehumidifiers designed for basements or crawl spaces during the summer peak ensures the reservoir never overflows. Even when the drainage path has horizontal runs or moderate elevation changes, the pump’s internal hydraulics are designed to keep the flow moving.

20 ft Vertical Lift Specification Enables Long-Distance Routing in Confined Spaces

The 20 ft vertical lift rating indicates the maximum head pressure this automatic condensate pump can handle. It means that you can install it in places where the drain outlet is much higher than the pump body. This specification directly affects whether HVAC systems installed below grade can be routed to drain exits above the floor.

The package includes a 20-foot drain hose, so you won’t need to buy any extra tubing during installation. Technicians can run drainage paths through wall cavities, ceiling chases, or equipment closets without affecting the system’s ability to keep a steady flow of water up the length of the tubing.

Upgraded Non-Return Check Valve Prevents Backflow During Intermittent Operation

When the pump is off, the built-in check valve uses a non-return ball mechanism to physically prevent water from flowing backward. This design is very important for installations where drain lines carry leftover water pressure or where elevated piping segments cause water to flow back down.

If a check valve doesn’t work properly, condensate pumps in applications that only need to run for short periods often experience water hammer and seals that wear out too soon. Because of the valve design in this unit, the pump chamber is isolated from downstream pressure while the unit is on standby. It greatly increases the life of both the valve seat and the motor.

≤40 dB Noise Rating Makes It Compatible With Noise-Sensitive Living Spaces

The pump’s sound output stays at or below 40 decibels when measured 1 meter away under normal operating conditions. It is about the same level as a quiet library. This level of performance is possible because the motor is mounted to reduce vibration, and the impeller geometry is optimized for hydraulics, which reduces turbulent flow noise.

This low acoustic profile is good for bedroom installations next to wall-mounted mini-split units or living room dehumidifiers. This model’s start-stop operation reduces mechanical transient noise, unlike regular condensate pumps that make a clicking sound when the float is turned on.

Built-In Safety Switch and Overheat Protection Safeguard Connected HVAC Equipment From Pump Failure Damage

When the pump detects an overload or a blocked discharge line, the safety switch activates to help prevent water from overflowing and damaging the connected air conditioning and furnace systems. This intervention at the circuit level protects costly HVAC components without requiring manual monitoring.

Overheat protection adds another layer of safety by monitoring the motor winding temperature and shutting down before overheating causes the insulation to break down. This thermal threshold management is important for keeping the pump in optimal condition over multi-season service intervals in furnace and boiler applications, where condensate temperatures can approach 122°F.

0.5-Gallon Tank With Five Inlets and 115V Input Supports Versatile Automatic Condensate Pump Integration

The 0.5-gallon reservoir has enough buffer volume to handle changing condensate input rates from equipment with non-linear output cycles, like two-stage furnaces or compressors that can change speed. Five inlet ports with different diameters can connect pipes from multiple upstream equipment sources simultaneously.

This pump runs on standard 115V single-phase power and doesn’t need a separate electrical circuit or step-down transformer in North American homes or small businesses. The included adapter set and cable ties simplify installation, reducing setup time and ensuring the hose is routed safely from the first use.