VEVOR 2200 lbs Electric Chain Hoist, 10 ft Lifting Height, 120V Single Phase Overhead Crane with 328 ft Wireless & 8 ft Wired Remote Control, Power Electric Hoist for Factories, Warehouses, Garages

VEVOR Electric Chain Fall Hoist Lifts 2,200 Lbs on a Dual-Chain System with 120V Single-Phase Power

When lifting things from above, unbalanced loads can cause dangerous swing forces that can hurt workers and damage equipment. The VEVOR electric chain fall hoist features a dual-chain load distribution system that evenly distributes 2,200 lbs (1,000 kg) of lifting capacity across both chains simultaneously. It helps reduce load sway under heavy loads on AC 120V, 60Hz power.

This combination of power and balance makes the unit ideal for removing engines, moving heavy parts, and handling structural steel in factories, warehouses, and garages without requiring three-phase power. Because it works with standard single-phase 120V outlets, the hoist can be plugged into existing circuits in most North American buildings without major electrical upgrades.

Dual-Speed Operation at 13.2 ft/min and 6.6 ft/min Balances Rapid Lifting with Precise Load Positioning

Single-speed hoists make it hard for operators to choose between a fast lifting speed and the precise control needed to place the load correctly at the end. This electric chain fall hoist solves that problem by giving you two speeds to choose from: 13.2 ft/min for quickly covering vertical distance during lifts with no obstacles, and 6.6 ft/min for slowing down during precise placement where precise positioning is required.

The smooth transition between speed modes lets operators lift quickly through open air and then switch to the lower speed as the load approaches its target location, without jerking the chain or making the suspended weight unstable. This ability is especially important when installing engines into engine bays, moving heavy machinery onto mounting pads, or lowering steel parts onto connection points with very tight alignment tolerances.

328-Foot Wireless Remote and 8-Foot Wired Pendant Provide Flexible Control Across Any Facility Layout

The operator’s position during overhead lifts directly affects both safety and load accuracy, but fixed-pendant hoists allow movement only along the length of the cord. The VEVOR electric chain fall hoist comes with an 8-foot wired pendant for close-range control and a wireless remote that works up to 328 feet (100 meters).

The wireless range is suitable for large warehouse bays, open factory floors, and multi-bay garages. The operator needs to be able to move between the load origin and destination during a single lift cycle. When both control options are available on a single unit, operators can choose the method that best fits the current task, rather than changing the workflow to accommodate the equipment’s limitations.

Upper and Lower Limit Switches, Auto-Braking, and Emergency Stop Deliver Multiple Safety Features

If one safety feature fails while a 2,200-pound lift is in the air, it could cause significant damage to the equipment and injure people. Built-in safety features help reduce this risk: upper and lower limit switches that stop the chain from moving before it goes too far, automatic braking that kicks in right away when the power goes out to keep the load still, and a separate emergency stop that stops all movement right away when the operator presses the button.

This layered design helps reduce the risk of load drop or chain overtravel if one part fails. Automatic brake engagement on power loss is especially important in areas with power outages, because it prevents an uncontrolled descent if the motor power fails in the middle of a lift without a mechanical holding system.

G100 Alloy Steel Chain and 360-Degree Rotating Forged Hook Withstand Repeated Heavy-Load Cycles

The long-term reliability of a hoist depends more on the integrity of the chain and hook under cyclic stress than on any other mechanical part in the lifting assembly. The VEVOR electric chain fall hoist uses a G100 alloy steel chain, which has a higher working load limit than the standard G80 chain of the same diameter. It also has a forged hook that rotates 360 degrees, preventing torsional load buildup in the chain when the load is lifted and rotated naturally.

Forged hooks don’t bend under shock loading, unlike cast hooks that do when they are suddenly loaded. This chain-and-hook combination can withstand the daily lift cycles common in production environments without fatigue, cracking, spreading, or deformation, unlike lower-quality hardware that does after heavy use.

IP54-Rated Motor with F-Class Insulation and Cooling Fan Sustains Performance in Dusty Industrial Environments

Motors used in factories and garages are constantly exposed to metal particles, sawdust, and other debris that can get into unprotected housings and damage winding insulation over time. This electric chain hoist has an IP54-rated motor that helps protect against dust ingress and can handle water splashes from all sides. The F-class insulation maintains dielectric integrity at winding temperatures up to 155°C, which can occur during heavy-lift operations.

The built-in cooling fan helps reduce heat buildup during extended use. It means operators don’t have to stop between lifts or wait for the motor to cool down before resuming work. The hoist can keep up with high lift rates in industrial settings where the temperature and humidity levels are too high for motors that meet lower environmental and thermal standards.

Electric Chain Fall Hoist Aluminum Housing, and 10-Foot Lift Height Optimize the Hoist for Overhead Installation

The choice of housing material for overhead equipment affects both the static dead load that is transferred to mounting structures and the unit’s ability to resist corrosion from oil mist, humidity, and chemical vapors in the workshop. The VEVOR electric chain hoist features an aluminum housing, making it lighter than steel-housed models. It means that I-beams, trolleys, and ceiling mounts that support the installation point may not require the same load capacity.

The 10-foot lift height accommodates standard garage ceiling clearances and typical warehouse bay heights where engine hoisting, pallet lifting, and equipment transfer operations occur most frequently. This height specification covers the majority of practical overhead lifting applications without requiring additional chain extensions for common tasks, making the unit ready for immediate productive use after installation without supplemental hardware purchases.